Victron Energy VE.Bus 3000 VA/2400 W MultiPlus Inverter/Charger

The MultiPlus, as the name suggests, is a combined inverter and charger in one elegant package. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology, plus multiple system integration features.

Feature Bullets

• Unique PowerAssist feature - The MultiPlus will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery
• Uninterrupted AC power (UPS function) - In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption
• Virtually unlimited power thanks to parallel operation - Up to 6 units can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible
• Remote Monitoring and Control - When coupled with a GX device (e.g. Cerbo GX) you can monitor and control your MultiPlus and system or systems locally (via LAN) or remotely (via the internet) from anywhere in the world, using the free VRM app and the free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, from adjusting your MultiPlus to auto starting a backup generator and more
• Multifunctional, with intelligent power management - The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure
• Two AC Outputs - The main output has no-break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore-/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater for example, can be connected to this output (second output available on models rated at 3kVA and more)
• Virtually unlimited power thanks to parallel operation - Up to six Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units, for example, provide 15kW/18kVA output power with 420 Amps of charging capacity
• Three phase capability - In addition to parallel connection, three units can be configured for three-phase output. But that's not all: with three strings of six parallel units a 45 kW/54 kVA three phase inverter and 1260 A charger can be built
• Split phase options - Two units can be stacked to provide 120-0-120 V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30 kW/36 kVA of split phase power. Alternatively, a split phase AC source can be obtained by connecting our autotransformer
• PowerControl - Dealing with limited generator, shore side or grid power - The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 20 A per 3 kVA MultiPlus at 120 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded
• PowerAssist - Boosting the capacity of shore or generator power - This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery
• Four stage adaptive charger and dual bank battery charging - The main output provides a powerful charge to the battery system by means of advanced 'adaptive charge' software. The software fine-tunes the three stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, the MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery
• System configuring has never been easier After installation, the MultiPlus is ready to go - If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed! Alternatively, VE.Net can be used instead of the DIP switches. And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several new, advanced, features
• Digital Multi Control - A convenient and low cost solution for remote monitoring, with a rotary knob to set PowerControl and PowerAssist levels
• VE.Bus Smart Dongle - Measures battery voltage and temperature and allows monitoring and control of Multis and Quattros with a smartphone or other Bluetooth enabled device
• Color Control GX and other GX devices - Provides monitor and control. Locally, and also remotely on the VRM Portal
• MK3-USB VE.Bus to USB interface - Connects to a USB port
• VE.Bus to NMEA 2000 interface - Connects the device to a NMEA2000 marine electronics network
• BMV-712 Smart Battery Monitor - Use a smartphone or other Bluetooth enabled device to: customize settings, monitor all important data on single screen, view historical data, and to update the software when new features become available
• VE.Bus communication port For parallel and three phase operation, remote monitoring and system integration

Specifications:

Width: 258 mm
Height: 362 mm
Depth: 218 mm
Material: Aluminum
Color: Blue (RAL 5012)
Continues Power at 25 deg C: 3000 VA/2400 W (Inverter)
Continues Power at 40 deg C: 2200 W (Inverter)
Continues Power at 60 deg C: 1700 W (Inverter)
Peak Power: 6000 W (Inverter)
DC Input Voltage Range: 19-33 V (Inverter)
Output AC Voltage: 120 VAC +/-2% (Inverter)
Output AC Frequency (Adjustable): 60 Hz +/-0.1% (Inverter)
Maximum Efficiency: 93% (Inverter)
Zero-Load Power: 20 W (Inverter)
Zero-Load Power in AES Mode: 15 W (Inverter)
Zero-Load Power in Search Mode: 8 W (Inverter)
Protection: A-G
Battery Connection: M8 Bolts
Protection Category: IP21
Operating Temperature: -40 to 65 deg C (Fan Assisted Cooling)
Humidity (Non-Condensing): Maximum 95%
Remote On/Off: Yes
AC Input Voltage: 95-140 VAC (Charger)
AC Input Frequency Rating: 45-65 Hz (Charger)
Charge Voltage Absorption: 28.8 VDC (Charger)
Charge Voltage Float: 27.6 V (Charger)
Storage Mode: 26.4 V (Charger)
Charge Current House Battery: 120 A (Charger)
Charge Current Starter Battery: 4 A (Charger)
Battery Temperature Sensor: Yes
120 VAC Connection: Screw Terminals 13 mm2 (6 AWG)
PowerControl/PowerAssist: Yes
Three Phase and Parallel Operation: Yes
Transfer Switch: 50A
Programmable Relay: Yes (3x)
Auxiliary Output: 32 A
General Purpose Com Port: Yes (2x)
Standards: EN-IEC 60335-1, EN-IEC 60335-2-29, EN-IEC 61000-3-2/3-3/, EN-IEC 61000-6-1/6-2/6-3, TUV, ETL Listed, PV Cycle, MCS, IEC
Warranty: 5 Years Limited
Weight: 40 lb